Nevada HVAC Pros
Ice-covered and snow-laden tree branches in the foreground of a snowy residential street, with a house visible in the background.

HVAC Installation in Ely, NV

A new system here will heat from September through June and cool from July through August every year. Tell us about the house, and a licensed contractor who covers White Pine County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An unfinished basement featuring exposed ceiling joists, a metal HVAC unit with round ductwork, a hanging light bulb, and scattered boxes and debris along the left wall.

Ely asks a new system to run almost year round

Winter nights here average 17°F from December through February, and homes need heat from September through June. That is ten months of heating. Summer only asks for cooling in July and August, when afternoons average 82°F, but between the two seasons a system in Ely is working nearly all twelve months.

A new furnace or heat pump has to be sized for those 17°F nights, not for a mild average. On the cooling side, 82°F afternoons are a lighter load, so the two halves of the system are not carrying equal weight. Most homes here heat with electricity, so a power outage means no heat as well as no lights. White Pine County saw 226 winter storms and 246 damaging wind events over the last ten years, and statewide, 13% of Nevada households went at least 24 hours without power in 2024. That is worth planning around when deciding how a new system is installed and backed up.

10 months
September through June, your system heats
2 months
July through August, it cools
17°F
the average winter night it heats against
82°F
the average summer afternoon it cools against
Isometric cutaway illustration of a single-story house with a dark shingled roof, showing interior rooms with furniture, ductwork, a flue pipe, and a furnace unit.
Your system heats September through June and cools July through August.

NOAA nClimDiv, 1991–2020 normals

Nevada requires HVAC contractors to hold a state license.

The Nevada State Contractors Board tests contractors before issuing an HVAC license, and it keeps a record of who holds one. The license belongs to the contractor, not to any single job, so it is the company or person doing the install who has been tested and licensed.

With a licensed contractor doing the work, the license is what stands behind it. Installing a heating and cooling system also needs a permit from the local building office in most cities and counties, with an inspection once the job is done. That inspection checks the installation itself, separate from what the license covers.

Sources: Nevada Legislature · Nevada State Contractors Board

When should I replace my HVAC system?
Replace it when repairs start costing more than they're worth, or when the system can't keep up anymore. A furnace or air conditioner that breaks down every season, or one that's aged past what a contractor considers a reasonable repair, is telling you something. Here, the furnace runs from September through June, so it carries most of the load in your home. When it starts struggling, you'll likely notice before summer even comes around, since cooling only runs through July and August. A contractor can look at the age and condition of your equipment and tell you whether another repair makes sense or whether it's time to replace.
Should I replace my furnace and air conditioner at the same time?
If both are old, replacing them together often makes sense, but it depends on the condition of each one. A furnace and air conditioner installed at the same time tend to wear at a similar rate, so if one is failing, the other may not be far behind. With winter lows here averaging 17°F, the furnace does the heavy lifting most of the year, so its condition matters more. A contractor can check both systems and tell you whether one needs attention now or whether it makes sense to plan for both.
What happens during an HVAC installation?
A contractor removes the old furnace and air conditioner, or heat pump, and puts in the new equipment, connecting it to the existing ductwork, gas line or electrical circuit, and venting. Before that, they size the equipment for the house so it matches the heating and cooling load rather than just swapping in something similar. Once installed, they test the system to make sure it starts, runs and shuts off the way it should. In most cities and counties here, this job needs a permit from the local building office, and the work gets inspected when it's done.