Nevada HVAC Pros
A snow-covered two-story house photographed at night during a snowstorm, with a single illuminated window visible on the front façade.

Furnace Installation in Crescent Valley, NV

A new furnace here will run from September through June every year. Tell us about the house, and a licensed contractor who covers Eureka County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An unfinished basement featuring a grey forced-air furnace with metal ductwork, concrete block walls, exposed wooden joists, and a single hanging bare bulb.

Ten months of heat in Crescent Valley

Furnaces here work September through June. That is ten months of the year, with only two off. Winter nights average 18°F, so a new furnace has to hold a house warm through long stretches of real cold, not just take the edge off.

A new gas furnace has to meet a federal minimum of 80.0 percent AFUE if it is a non-weatherized model built after November 2015. Power loss is worth planning around too. Across Nevada, 13% of households lost power for 24 hours or more in 2024, and the area has logged 101 winter storms and 97 damaging wind events over the past ten years. When the power drops on a cold night, a furnace that restarts cleanly on its own matters.

10 months
September through June, your furnace is on duty
18°F
the average winter night it heats against
80% AFUE
the federal minimum any new unit must meet
Isometric cutaway illustration of a small single-story house showing interior rooms with furniture, a furnace unit with attached ductwork running to a roof flue, and a dark shingled roof.
Your furnace works hardest from November through April.

NOAA nClimDiv, 1991–2020 normals

Nevada requires HVAC contractors to hold a state license.

That license means the state tested this contractor before letting them take on furnace work, and the Contractors Board has a record of them. It covers the contractor as a whole, not this one job. They already had to earn it to work in the trade at all, not just for your installation.

For this job, that license is what stands behind the person doing the work. Eureka County still has its own part in this. In most cities and counties, replacing a furnace needs a permit from the local building office and an inspection once the work is done. That inspection is what checks the gas connections and venting are safe.

Sources: Nevada Legislature · Nevada State Contractors Board

What size furnace does my house need?
It depends on your house, not a rule of thumb like square footage alone. A contractor works out the size with a load calculation that accounts for your home's insulation, window area, ceiling height, and air leaks. Going by square footage guesses gets you a furnace that's too big, which cycles on and off and never runs long enough to heat evenly, or too small, which runs constantly and still can't keep up when it's 18°F outside. With heat needed here from September through June, getting the size right matters more than in places with a short winter.
How do I know it's time to replace my furnace?
Start with the age. Furnaces built after November 2015 are required to run at 80 percent AFUE or higher, so if yours is older than that, a newer unit is likely burning less gas for the same heat. Beyond age, watch for repairs that keep coming back, a furnace that can't hold a steady temperature, or a rise in your gas bill without a reason. Since homes here need heat 10 months out of the year, a furnace on its way out gets far less rest than it would somewhere with a short winter, which tends to speed up the decline.
Is a high-efficiency furnace worth it?
It depends on how much you run the furnace and how old your current one is. Homes here need heat from September through June, so a furnace is doing more work over the year than in most places, and that's exactly the situation where a jump in AFUE adds up over time. Every furnace built since November 2015 has to hit at least 80 percent AFUE, so the real question is whether stepping up further makes sense for your house. A contractor can run the numbers for your specific furnace and usage rather than a general rule.